{"product_id":"mini-vgate-wifi-icar-iv350-elm327-obdii-obd2-diagnostic-scanner","title":"Mini Vgate WIFI ICar IV350 ELM327 OBDII OBD2 Diagnostic Scanner","description":"\u003cspan style=\"font-size:16px;\"\u003e\u003cspan\u003e\u003cspan style=\"\"\u003e\u003cstrong\u003e\u003cu\u003e\u003cem\u003eMini Vgate WIFI ICar IV350 ELM327 OBDII OBD2 Diagnostic Scanner for iOS Android\u003c\/em\u003e\u003c\/u\u003e\u003cbr\u003e\u003cbr\u003eFeatures:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e1. Fully compatible with ELM327 V1.4b.\u003cbr\u003e2. All ELM327 supported software are available to use.\u003cbr\u003e3. Faster than ELM327 four times or higher. (ELM327 is RISC 8bit 44MHz MCU, iCar is ARM 16bit MCU)\u003cbr\u003e4. Due to the android diagnostic software becomes heavier to run, suggest to use on smart phone with CPU 800Mhz or higher, 1GHz recommended.\u003cbr\u003e5. Built in power switch.\u003cbr\u003e6. Low standby power consumption sleep mode.\u003cbr\u003e7. Lower power consumption than ELM327\u003cbr\u003e8. LED indicator is in the front side toward user for easier check of linking status.\u003cbr\u003e9.  Support J1939 protocol more than ELM327.\u003cbr\u003e10. WiFi 802.11 b\/g or 802.11n module. \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e1. OBDII decode chip: ARM 16bit MCU\u003cbr\u003e2. Firmware: ELM327 Version 1.4b compatible\u003cbr\u003e3. Transfer baud rate: 4800 \/ 9600 \/ 10400 \/ 38400 (default) \/ 115200 \/ 500K\u003cbr\u003e4. Input interface: OBDII male 16pin\u003cbr\u003e5. Output interface: Wifi 802.11 b\/g or 802.11n after 2013 Feb 01\u003cbr\u003e6. LED Indicator: Power(red) \/ OBD(green) \/ Link(blue) (PC or smart phone)\u003cbr\u003e7. Operating Voltage: 12V from car OBD2 socket, including over voltage \/shortage protection\u003cbr\u003e8. Nominal Idle current: 45mA\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003cdiv\u003e\u003cspan style=\"font-size:16px;\"\u003e\u003cspan\u003e\u003cspan style=\"\"\u003e9.Communication range: 500m open field\u003cbr\u003e10.SSID: VGATE (discontinued) or BUYOBD (current)\u003cbr\u003e11.Encryption: Open (VGATE) and WEP shared\/WEP128 (BUYOBD)\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/div\u003e\u003cbr\u003e\u003cspan style=\"\"\u003e\u003cspan style=\"\"\u003e\u003cspan style=\"font-size:16px;\"\u003e\u003cstrong\u003eUsage:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e1. Keep car key at off position\u003cbr\u003e2. Plug the Vgate scantool into Car OBDII female socket.\u003cbr\u003e    OBD2 socket is usually below the driving wheel.\u003cbr\u003e    The Vgate should blink all 3 LEDs and off again.\u003cbr\u003e    Only red power LED remains on.\u003cbr\u003e3. Insert car key.\u003cbr\u003e4. Switch car key to Accessory ON position,\u003cbr\u003e5. Turn on WiFi of PCtebook\/smart phone.\u003cbr\u003e  Check Windows control panel\u0026gt;wireless network\u0026gt;Setting\u0026gt;Advanced\u0026gt;Wireless mode\u0026gt;IEEE 802.11b\/g\/n.\u003cbr\u003e  Check android wifi setting, turn off existing link.\u003cbr\u003e  Check iPhone Wi-Fi networks, turn off existing link.\u003cbr\u003e6. Scan the Vgate wifi device from your Desktop\/Notebook PC\/PDA\/phone.\u003cbr\u003e   Find SSID \"VGATE\" or \"BUYOBD\".\u003cbr\u003e   The Vgate blue LED should be on now. Otherwise, the device doesn't respond to the scanning.\u003cbr\u003e7. For Windows\/Android,\u003cbr\u003e   If SSID is \"VGATE\", it is DHCP mode, not need to set up. \u003cbr\u003e   If SSID is \"BUYOBD\", enter 13 digits password shown on the label of the white plastic case.\u003cbr\u003e   IP: select \"Fixed\", and enter \"192.168.0.10\"\u003cbr\u003e   Subnet mask: enter \"255.255.255.0\"\u003cbr\u003e   DNS: keep blank\u003cbr\u003eFor iPhone\/iPad:\u003cbr\u003eIf SSID is \"VGATE\", it is DHCP mode, not need to set up.\u003cbr\u003eIf SSID is \"BUYOBD\", enter 13 digits password shown on the label of the white plastic case.\u003cbr\u003eIP: change from \"DHCP\" to \"Fixed\"!\u003cbr\u003eIP: enter \"192.168.0.11\" or later\u003cbr\u003eSubnet mask: enter \"255.255.255.0\"\u003cbr\u003eHTTP local port: enter \"35000\"\u003cbr\u003e8. App setup: select Vgate device as KiWi wifi or ELM327.\u003cbr\u003e   Click link, app will build a link to Vgate.\u003cbr\u003e   App may take time for scaning vehicle protocol less than a minute or so.\u003cbr\u003e   App starts to show static data once recognize the protocol and has correct table of  associated sensor.\u003cbr\u003e   The Vgate green LED should be blinking now.\u003cbr\u003e   The faster data rate the protocol is, the the faster the green LED blinks.\u003cbr\u003e   Turn off the app, not minimize\", if app fails to link and doesn't show data. Start another app and try again.\u003cbr\u003e   Some vehicles may have to turn car key to \"ON\/Start\" position to activate car ECU.\u003cbr\u003e   Turn car key to \"ON\/Start\" position to read real-time data.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eCommunication  Protocol:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eOBDII 16-pin DLC definition: \u003cbr\u003e1. n\/a\u003cbr\u003e2. Bus + (SAE J1850 PWM, VPW)\u003cbr\u003e3. n\/a\u003cbr\u003e4. Battery -\u003cbr\u003e5. Signal -\u003cbr\u003e6. CAN High (ISO 15765-4)\u003cbr\u003e7. K Line (ISO 9141-2, SAE J2234)\u003cbr\u003e8. n\/a\u003cbr\u003e9. n\/a\u003cbr\u003e10. Bus - (SAE J1850 PWM, VPW)\u003cbr\u003e11. n\/a\u003cbr\u003e12. n\/a\u003cbr\u003e13. n\/a\u003cbr\u003e14. CAN Low (ISO 15765-4)\u003cbr\u003e15. L line (ISO 9141-2, ISO 14230-4)\u003cbr\u003e16. Battery +\u003cbr\u003eOnly pins 2, 4, 5, 6, 7, 10, 14, 15, 16 defined by above standards read data.\u003cbr\u003eOther customized pins are not supported.\u003cbr\u003ePlease confirm OBDII label located under front engine hood. \u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSupport OBDII\/EOBD2 protocols:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eISO 15765-4 (CAN-B 125Kbps, started since 2003 in USA)\u003cbr\u003eISO 15765-4 (CAN-C 500Kbs, 11bit ID, 29bit ID, started since 2003 in USA)\u003cbr\u003eISO 14230-4 (KWP2000) \u003cbr\u003eISO 9141-2 (5 baud init. 10.4 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)\u003cbr\u003eSAE J1850 VPW (10.4 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)\u003cbr\u003eSAE J1850 PWM (41.6 kbaud, replaced by 14230-4 gradually, stopped in USA in 2008)\u003cbr\u003eSAE J1939 the Data link connector standard\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eFunction:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e1. Read more than 3000 car manufacturers' stand DTC and private DTC (diagnostic trouble codes) and its meaning.\u003cbr\u003e2. Clear DTC, turn off dashboard MIL \"Check Engine\" Light\u003cbr\u003e3. Display sensor data, including: \u003cbr\u003eEngine RPM \u003cbr\u003eLoad\u003cbr\u003eCoolant Temperature\u003cbr\u003eFuel Status\u003cbr\u003eVehicle speed\u003cbr\u003eIntake Manifold pressure (MAF\/MAP)\u003cbr\u003eTiming Advance\u003cbr\u003eIntake Air Temperature\u003cbr\u003eAir Flow Rate\u003cbr\u003eAbsolute Throttle Position\u003cbr\u003eOxygen sensor voltage \/short term fuel trim\u003cbr\u003eFuel Pressure\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eSoftware Support:\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/span\u003e","brand":"Electronic Pro","offers":[{"title":"Default Title","offer_id":14352028401708,"sku":"915531","price":590.38,"currency_code":"ZAR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/2787\/9162\/products\/SKU115214c.jpg?v=1554194446","url":"https:\/\/electronic-pro-south-africa.myshopify.com\/products\/mini-vgate-wifi-icar-iv350-elm327-obdii-obd2-diagnostic-scanner","provider":"Electronic Pro ","version":"1.0","type":"link"}